-40%
Motogadget Mo. Unit Bluetooth ECU Digital Cables Sensor M5 Magneti
$ 342.09
- Description
- Size Guide
Description
Motogadget M Unit Blue + Cable Kit + Speed Sensor and 2 magnetsMotogadget M-Unit Blue with M-Unit cable kit
Scope of delivery:
• 1x M.unit Blue + M-Unit cable kit as shown without the red battery cable!
• 1 speed sensor with 2 magnets
• Detailed instructions for installation and use
1x M Drive Cable Kit
Cable color / section / length [m] / number
brown / 2.5 mm² / 5
black / 2.5 mm² / 4
blue / 2.5 mm² / 2
white / 1.5 mm² / 4
red / 1.5 mm² / 2
yellow / 1.5 mm² / 4
orange / 1.5 mm² / 4
green / 1.5 mm² / 2
purple / 1.5 mm² / 2
white / 0.5 mm² / 2
blue / 0.5 mm² / 2
red / 0.5 mm² / 2
yellow / 0.5 mm² / 2
green / 0.5 mm² / 2
orange / 0.5 mm² / 2
purple / 0.5 mm² / 2
brown / 0.5 mm² / 2
Small cable tie 15
Large cable tie 15
Small cable lugs 10
Medium tips 10
Large tips 10
operative manual
The red battery cable is no longer supplied by Motogadget!
You can find article 362-001 (without fuse) and article 362-000 (with 40 A fuse) in the shop!
The new m.unit blue has been further developed and significantly improved over the proven previous version. It now has 12 inputs and 10 outputs, interchangeable quality cable clamps, and most importantly, Bluetooth® LE. This allows you to connect m.unit blue directly to our m.ride app on your smartphone. This functionality is unique in the motorcycle accessories industry.
The entire configuration and alarm system can be controlled via the m.ride app. Fault diagnosis is also possible during operation and without removing the m unit. You can also use a secure and encrypted keyless go function.
Once activated, simply approach with your smartphone to prepare the vehicle for departure. Thus, the on-board voltage can be activated by pressing the start button. Pressing it again starts the engine. Once switched on, the vehicle's electrical system remains safely activated while driving, even without a phone.
The m.unit blue is the digital control unit for a motorcycle, the heart of the entire vehicle electrical system. It can be operated with push button controls or with conventional switch handlebar controls. It switches all the necessary components on the vehicle and at the same time takes over the tasks of the electrical fuses.
Relays and individual wiring components are significantly reduced and new minimized vehicle wiring can be done in the shortest time possible.
When using the m button, the number of all panel connections is reduced to a single wire.
Functions WITHOUT smartphone and m.ride app:
• Full digital button control, 4 or 5 button operation possible
• Complete replacement of the fuse box. 10 independent circuits are digitally monitored and shut down in the event of a fault. After the error has been cleared, the safety function is automatically reset
• Integrated, location-independent alarm system
• Integrated, digital, load independent flasher relay, optional and adjustable automatic shutdown, selectable m.wave mode
• Integrated emergency lights
• Indicators can optionally be set as position lights
• Integrated position light and flasher
• Control of low and high beams (switching capacity up to 200 W) with a single button
• Integrated digital stop light modulator, programmable flashing mode
• Acceleration-controlled emergency brake light (automatic warning signal)
• Integrated starter relay for starters with magnetic switches (switching capacity up to 30 A)
• Intelligent and configurable control / disconnection of utilities in order to use the maximum starting energy of the battery during the starting process
• Integrated digital horn relay
• Two configurable auxiliary outputs AUX1 and AUX2
• Diagnostic function for assigning inputs, outputs, circuit switching status, short-circuit diagnosis, etc.
• Calibration and current measurement allow for defect detection of all lamps
Functions WITH smartphone and m.ride app:
• Encrypted connection via Bluetooth® LE (Low Energy), thus protection against manipulation
• Extremely low power consumption of smartphones and m.unit blue (with Bluetooth active 0.9 mA and in power saving mode after 6 weeks of inactivity: 0.3 mA)
• Keyless-Go (ready to start the vehicle by approaching it with your smartphone)
• The highly sensitive acceleration sensor allows you to view your driving activity in m.ride using an activity factor, number of turns, maximum speed, etc.
• Transmission of alarm events (with date, time, ground vehicle, etc.) to the app
• Setting the mode and sensitivity of the alarm system
• Monitoring of the current battery voltage in the app
• Diagnosis of all inputs and outputs, measurement of currents, voltage, device temperature
• Defect detection of all lamps by calibration. Defective turn signals double the flash rate, the status message in the app and the audio message from Rideassist.
•
The new m.unit blue has been further developed and significantly improved over the proven previous version. It now has 12 inputs and 10 outputs, interchangeable quality cable clamps, and most importantly, Bluetooth® LE. This allows you to connect m.unit blue directly to our m.ride app on your smartphone. This functionality is unique in the motorcycle accessories industry. Once activated, simply approach with your smartphone to prepare the vehicle for departure. Thus, the on-board voltage can be activated by pressing the start button. Pressing it again starts the engine. Once switched on, the vehicle's electrical system remains safely activated while driving, even without a phone. The m.unit blue is the digital control unit for a motorcycle, the heart of the entire vehicle electrical system